Mint Thread Lift in Korea: How Barbed PDO Threads Lift the Mid-Face

Short answer: A Mint thread lift uses absorbable PDO (polydioxanone) threads with small barbs that grip soft tissue and lift it into a higher position. In the mid-face, this can raise drooping cheeks, soften nasolabial folds and improve the jawline, with a visible change straight away. The threads dissolve over several months while stimulating collagen around them. Results typically last around a year or more, and recovery usually involves swelling and tenderness for one to two weeks.
What is a Mint thread lift?
Mint is a brand of barbed PDO lifting thread developed in Korea and used in many countries. PDO is a material that has long been used in absorbable surgical sutures. Mint threads are thicker and stronger than the fine "mono" threads used for skin quality, and they carry barbs moulded along their length. Those barbs are what allow the thread to hold and lift tissue rather than simply sit under the skin.
An overview of the Mint thread lift in Seoul describes the main treatment areas, which commonly include the cheeks, jawline, jowls and neck.
How do barbed PDO threads lift the mid-face?
- Insertion: after local anaesthetic, a doctor inserts each thread through a small entry point, usually near the hairline or in front of the ear, using a blunt cannula or needle.
- Anchoring: the thread runs through the fatty layer along a planned vector. The barbs face in one direction so they grip tissue as it is gently pulled upwards.
- Repositioning: the doctor lifts and shapes the tissue, then trims the thread ends below the skin.
- Collagen response: over the following months, the body forms collagen around the threads as they slowly dissolve, helping maintain support.
In the mid-face, threads are often placed to lift the cheek fat pad back towards the cheekbone. That can soften the fold beside the nose and reduce early jowls further down.
Mint threads compared with other thread types
| Thread type | Design | Main purpose | Lift strength |
|---|---|---|---|
| Mono PDO threads | Smooth, very fine | Skin quality and fine texture | None to minimal |
| Cog or barbed PDO (e.g. Mint) | Barbs moulded or cut along thread | Lifting and repositioning tissue | Moderate |
| PLLA or PCL threads | Barbed or coned, different material | Lifting with longer collagen effect | Moderate, often longer-lasting |
The right thread depends on your anatomy, skin thickness and the result you want. A guide to PDO thread lifts in Korea explains the different options in more detail.
Who is a good candidate?
- People in their 30s to 50s with mild to moderate mid-face or jawline sagging.
- Those wanting a visible lift without surgery or general anaesthesia.
- Patients with reasonable skin thickness and some soft tissue to hold.
Threads are less suitable for very thin faces with little soft tissue, very heavy skin, or people prone to keloid scarring. They are usually avoided in pregnancy, with infection in the area, and with certain bleeding disorders or autoimmune conditions.
Combining Mint threads with other treatments
Threads reposition tissue, but they do not replace lost volume or tighten the skin surface. For that reason, many doctors build them into a wider plan. Focused ultrasound or radiofrequency can tighten the skin and deeper layers, while fillers or collagen stimulators can restore volume in the cheeks and temples so the lifted tissue has support. Skin boosters may improve texture over the threaded area.
Timing matters. Some doctors perform energy treatments before threads, or leave a gap of several weeks, so heat is not applied directly over fresh threads. Ask for the full plan, including the order of treatments and how long to wait between them. For a broader view of mid-face options, see this overview of the mid-face lift in Korea.
Recovery: what to expect
| When | What is typical |
|---|---|
| Day 0–3 | Swelling, tightness and tenderness, especially when chewing or yawning. Possible bruising. |
| Day 3–14 | Swelling settles. Mild dimpling or puckering near entry points often fades. |
| Weeks 2–4 | Tissue settles into its new position and the look becomes more natural. |
| Months 1–6 | Collagen forms around the threads as they dissolve. |
During the first one to two weeks, avoid wide mouth opening, firm facial massage, heavy exercise, saunas and sleeping face down. Many doctors also advise avoiding dental work for a few weeks.
Risks and possible complications
Most side effects are temporary, but thread lifts are a medical procedure. Possible issues include:
- Bruising, swelling and asymmetry while healing.
- Visible or palpable threads, especially in thin skin.
- Dimpling or irregularities that persist beyond the first weeks.
- Infection or thread extrusion through the skin, which needs prompt review.
- Rarely, nerve irritation or prolonged discomfort.
Contact the clinic if you have increasing pain, redness, warmth, discharge, fever or a thread poking through the skin. If an earlier thread lift went wrong, revision needs careful assessment; this guide on revision thread lifts explains the usual approach.
Frequently asked questions
How long does a Mint thread lift last?
Results commonly last around 12 to 18 months, depending on the number of threads, your skin and your age.
Does a thread lift hurt?
Local anaesthetic is used, so most people feel pressure and tugging rather than sharp pain. Tenderness afterwards is common for several days.
How many threads are needed?
It varies with the area and degree of sagging. Your doctor should explain the number and placement before treatment.
Can threads be combined with HIFU or fillers?
Yes, combinations are common. Timing matters, so follow your doctor's guidance on the order of treatments.
When can I fly after a thread lift?
Many people fly within a few days, but swelling and tenderness may still be present. Allow time for a follow-up check before leaving if possible.
This article is general information, not medical advice. Thread lifts carry real risks, so discuss suitability, thread type and aftercare with a qualified doctor before treatment.


























